Review Anycubic Kobra Go 3D Printer Auto Leveling and ANYCUBIC PLA 3D Printer Filament (Purple) Bundle

• Facebook
• Twitter
• Line

Details: Anycubic Kobra Go 3D Printer Auto Leveling and ANYCUBIC PLA 3D Printer Filament (Purple) Bundle

Brand: ANYCUBIC

How to replace filaments1.Install the spool on the spool holder of a 3D printer, and preheat the nozzle2.Cut the top of the filament into a spire shape, and thread it into the extruder and feeding tube3.Manually push the filament through the feeding tube to the nozzle, until the filament melts through the nozzleExtra attention neededWhen installing and replacing filaments, make sure to heat the print head (heated to above 200°C), otherwise the print head might get clogged.

Buyer Guide 3D Printers

 3D Printers offer users the ability to create physical objects from digital files. Buying the right 3D Printer can be a daunting task and this guide is here to help you make the right decision.

• Budget. Budget is the biggest factor that should guide your buying decision. While a low-end printer may suffice for most users, the difference in print quality between a low-end and a high-end printer may not be worth the added cost.
• Nozzle Size. Nozzle size determines the size of the nozzle tip. A larger nozzle tip prints finer details, but requires more time to print. The tradeoff is that printing a large object may require more material.
• Filament Diameter. The filament diameter determines the diameter of the extruded thread. The thinner the filament the better the resolution, but the larger the print. The bigger the print, the longer it takes to print.
• Print Speed. Print speed determines how fast the printer can print, measured in mm/s. Higher print speeds allow you to print larger objects in a short time.
• Nozzle Change Time. The nozzle change will determine how quickly you can replace a nozzle tip. Changing a nozzle tip with a slow change time means you need to wait for the printer to cool down before you can replace the nozzle tip.

 

How to choose 3D Printers

When shopping for a 3D printer, there are a couple of key factors to keep in mind:

• How easy is the 3D printer to use? Buying a 3D printer can be intimidating, particularly if you’re not familiar with how it works. When choosing a printer, look for one that has a clear instruction manual, as well as clear and detailed guides online. Also, consider whether the 3D printer comes with software or is compatible with other platforms.
• Does the 3D printer work right? 3D printers aren’t cheap. Before you buy a 3D printer, it’s important to test it out and make sure it works right. Most 3D printers come with either an SD card or a USB flash drive, so it’s a good idea to download and test the 3D printer’s software before committing to the purchase.

How to maintain 3D Printers

 You probably already know that 3D printers are handy little devices. However, did you know that maintaining your 3D printer is just as important? You can have the best-quality printer on the market, but if you don’t take the time to maintain it, it won’t last long.

• Clean the print bed regularly. The bed is the part of the printer that holds the object to be printed. If the bed isn’t properly cleaned, your print may not come out as clean as you would like. Make sure the print bed is cleaned at least once a week, and more frequently as needed. Also, make sure you clean the print bed with warm, soapy water.
• Use a filament conditioner. Filament conditioners help clean the extruder and nozzle of the printer. They also help remove clogs from the extruder and help clean the filament when the print is done.
• Use an ultrasonic cleaner. Ultrasonic cleaners can be used to clean the break and nozzle of the printer. Ultrasonic cleaners can also be used to clean printer accessories, including filaments.
• Use a filament dryer. Filament dryers help remove moisture from the nozzle and print head, helping to prevent clogs.
• Use an air compressor to blow out the filament. If your printer filament is stiff or thick, you may want to use a compressor to blow the filament out to remove moisture.
• Use rubbing alcohol and cotton swabs to clean the print head. Sometimes, the filament can bend and clog your print head. To clean this area, mix 5% rubbing alcohol with cotton swabs, and gently clean the print head.

---

 

• Facebook
• Twitter
• Line